If necessary, disconnect the Ethernet cable or wireless adapter.Cumulus Linux 3.7.12 also includes a firmware update for Mellanox switches that addresses an issue with certain Virtium SSDs. (Nasdaq: MCHP), offers a comprehensive portfolio of semiconductor and system solutions for communications, defense & security, aerospace and industrial markets.If you are changing your TiVo boxs connection method to MoCA, go to 'Settings & Messages' > 'Network Settings' > 'Change Network Settings.' Then choose 'Connect using MoCA.' Join MoCA network using a TiVo Bridge. What's New in Cumulus Linux 3.7Microsemi Corporation, a wholly owned subsidiary of Microchip Technology Inc. 'SonicWall is a well-known manufacturer of hardware firewall devices, VPN gateways, and network security solutions whose products are commonly used in SMB/SME and large enterprise organizations.' They released an advisory warning that hackers used a bug in their Secure Mobile Access (SMA) VPN device and their NetExtender VPN client to attack.
![]() Spectrum Mss Sonicwall Vpn User Guide Update For MellanoxDynamic VRF route leaking is now supported for EVPN Virtual Router Redundancy Protocol (VRRP) 48V DC PSU for the Dell Z9100-ON switchCumulus Linux 3.7.5 fixes an issue with EVPN centralized routing on Tomahawk and Tomahawk+ switches ( RN-1353), an issue with switchd when IGMP snooping is enabled on a Broadcom switch ( RN-1369) and includes additional security fixes.Cumulus Linux 3.7.5 replaces Cumulus Linux 3.7.4 and includes all the new features and resolved issues from Cumulus Linux 3.7.4.Cumulus Linux 3.7.4 is no longer available due to severe issues that are resolved in Cumulus Linux 3.7.5.Cumulus Linux 3.7.4 contains a number of new platforms, features, and improvements: Ability to disable FEC on Mellanox switches IGMP/MLD snooping is supported over VXLAN bridges on Broadcom switches Multiple Dynamic Authorization Server (DAS) support ![]() The EVPN duplicate address detection freeze option lets you freeze a duplicate address permanently or for a certain amount of time Penguin Arctica NX4804x (10G Broadcom Maverick) Lenovo NE0152TO (1G Broadcom Helix4) now generally available RFC 5549 support with global IPv6 peers Support for egress IPv6 ACL rules on Broadcom switches Support for VRF route leaking on Mellanox switches On Facebook Voyager, the NCLU net show transponder command output shows the Optical Signal to Noise ratio (OSNR) in the network Lenovo NE0152TO (1G Helix4) - available for Early Access Lenovo NE2572O (25G Tomahawk+) - swp1 thru swp8 support 25G speed only Best code editor for mac with previewRADIUS Change of Authorization (CoA) requests Line side loopback and terminal loopback mode for Facebook Voyager troubleshooting Penguin Arctica 4806XT (10G Trident 2+) QCT QuantaMesh BMS T7032-IX7 (100G Trident3) QCT QuantaMesh BMS T4048-IX8 (25G Trident3) ![]() Before You Upgrade from Cumulus Linux 3.7.3 or EarlierIf you are using apt to upgrade to Cumulus Linux 3.7.4 or later, you must install the cumulus-trim package before upgrading. Follow the steps in the Cumulus Linux Quick Start Guide.Whether you are installing Cumulus Linux 3.7 for the first time or upgrading from an earlier version, follow the steps in the Installation Management section of the Cumulus Linux User Guide. Enabling front panel ports requires a license.After you receive a license key from Cumulus Networks or an authorized reseller, you can install the license. Only eth0 and console ports are activated on an un-licensed instance of Cumulus Linux. Each network system is fully operational, enabling any capability to be utilized on the switch with the exception of forwarding on switch panel ports. Change bond mode to IEEE 802.3ad link aggregation modeCumulus Linux is licensed on a per-instance basis. Open and Fixed Issues in Cumulus Linux 3.7.11 and 3.7.12Added CM-27937 (open issue), CM-27456 and CM-25973 (fixed issues)Added CM-27764 and CM-27737 (open issues)Added CM-28087, CM-28077, CM-28065, CM-27496 (open issues)Added CM-28076, CM-28007, CM-27999, CM-27957, CM-27927, CM-25665 (open issues)The following issues are fixed in Cumulus Linux 3.7.10. DocumentationYou can read the technical documentation here. Perl, Python and BDB ModulesAny Perl scripts that use the DB_File module or Python scripts that use the bsddb module do not run under Cumulus Linux 3.7. To ensure a smooth upgrade, follow the steps in Upgrading Cumulus Linux in the Cumulus Linux User Guide. Release Note IDThe following issue was added on November 25, 2019.The ospfd daemon might crash with a kernel traceThe ospfd daemon might crash with the following kernel trace: T23:00:08.261749+09:00 cumulus ospfd: Assertion `node' failed in file ospfd/ospf_packet. Equipment from other vendors might drop this traffic.This issue is fixed in Cumulus Linux 3.7.10.The following issues affect the Cumulus Linux 3.7.10 release.
0 Comments
Leave a Reply. |
AuthorAdam ArchivesCategories |